Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jsmitman82

Pages: [1]
1
Pumps, Wells, Tanks, Controls / Re: Off grid well
« on: October 06, 2021, 04:12:41 PM »
I haven't tested how fast the water level replenishes up to the current static level, which I assume would be different rates depending on how far it draws down, given the GPM measurement increased the deeper it went.  Given I lack that information, I'm a bit worried about setting it too shallow.  I'm also not sure if I intend to use it for irrigation and gardening in the future.  So I'm leaning towards setting it at probably 360', just a small buffer from the bottom.  Can/should I use 250psi HDPE pipe at that depth?

2
Pumps, Wells, Tanks, Controls / Re: Off grid well
« on: October 06, 2021, 11:29:48 AM »
The performance chart here shows the 10GS15 as doing 7.4gpm at 50psi, so it seems like I would need a 2hp to break 10gpm and/or 50psi (at 380 feet).
https://www.aquascience.net/media/catalog/product/G/o/Goulds_10gs15_7.gif

What do you think about the 250psi rated HDPE pipe vs PVC (schedule 80 or 120?) for this well, in the context of me maintaining it myself?  Sch120 PVC has much better pressure rating, but it seems like it would be a lot more opportunities for leaks between sticks, and I'm not sure which would be easier for me to install and remove when the day comes that I need to replace the pump.

So if I have a CSV/PRV after the pressure tank set to 40psi, and a pressure switch at the tank set for 40/60psi, I wouldn't have a constant 40psi after the CSV/PRV, while the pump only cycles once the tank drops from 60psi down to 40psi?

3
Pumps, Wells, Tanks, Controls / Re: Off grid well
« on: October 03, 2021, 11:03:43 PM »
Could you install a CSV after a large pressure tank?  I am wondering if you could achieve both constant pressure and maximize power efficiency (off grid concern), by combining a CSV and a large pressure tank, where the pump would run at BEP to fill the large tank, and then when water is drawn from the tank the CSV would keep the pressure down near the low end of the tanks pressure.  If not, is there another way to achieve this?

4
Pumps, Wells, Tanks, Controls / Off grid well
« on: October 01, 2021, 02:19:36 PM »
I had a well drilled, specs are:
380' deep
200' depth water first encountered @ 1gpm
240' depth water @ 3gpm
300' depth water @ 5gpm
340' depth water @ 8gpm
380' depth water @ 15gpm
30' static water level

I have a contractor lined up to build a house next spring.  I currently have no power at the property, but plan to incorporate a large off grid power solution (inverter, batteries, solar, generator, etc).  There are no buildings currently on the property with which to locate the components for a power or water system.  I would like to have water functioning before the house build starts, which also means before I have an off grid power solution.  My well driller is trying to sell me an expensive $8k VFD system (goulds 10gs30, 3as30, 3hp 3 phase motor, 4.25gal in well pressure tank) and saying that it is what he recommends for off grid people, with a plug for a generator at the pedestal that also contains the vfd drive.  After tons of research I am not convinced that this is in my best interest economically.  I am concerned not just for the longevity of the components in my water system, but also the total power requirements of it - not just power required to pump the water we will use but also the idle power draw of the VFD drive.  I am not sure a CSV is going to be the best path either (in terms of efficiency), but I do like the simplicity of it and what it offers.  If I want to go for maximum efficiency then any constant pressure solution is probably not the answer, but I'm not sure that I need to optimize that heavily - I just worry about low solar production in the winters in Northern Idaho, and reducing my need for running a generator during those months.  I'm not sure what to do, but I am concerned that I will regret moving forward with this expensive VFD system; however, I'm not sure what my alternatives are for my situation of needing water before I have a building where I could locate water system components like a pressure tank.  My water needs before the house is completed will be much different (no toilets flushing with no house), so I could add things like a pressure tank and CSV at that time... but I'm not sure if I could/should run a submersible pump off a generator with no pressure tank before the house is built.  I'm also wondering if it's possible to install 2 pumps of different sizes in the well (each on its own CSV), one for small flow and one for larger flow, where the small one would run most often and be more energy efficient due to being closer to its BEP.

Apologies if I've left out important details, my brain is fried after reading about wells for several hours.

Pages: [1]