Show Posts
1
Pumps, Wells, Tanks, Controls / Off grid well
« on: October 01, 2021, 02:19:36 PM »
I had a well drilled, specs are:
380' deep
200' depth water first encountered @ 1gpm
240' depth water @ 3gpm
300' depth water @ 5gpm
340' depth water @ 8gpm
380' depth water @ 15gpm
30' static water level
I have a contractor lined up to build a house next spring. I currently have no power at the property, but plan to incorporate a large off grid power solution (inverter, batteries, solar, generator, etc). There are no buildings currently on the property with which to locate the components for a power or water system. I would like to have water functioning before the house build starts, which also means before I have an off grid power solution. My well driller is trying to sell me an expensive $8k VFD system (goulds 10gs30, 3as30, 3hp 3 phase motor, 4.25gal in well pressure tank) and saying that it is what he recommends for off grid people, with a plug for a generator at the pedestal that also contains the vfd drive. After tons of research I am not convinced that this is in my best interest economically. I am concerned not just for the longevity of the components in my water system, but also the total power requirements of it - not just power required to pump the water we will use but also the idle power draw of the VFD drive. I am not sure a CSV is going to be the best path either (in terms of efficiency), but I do like the simplicity of it and what it offers. If I want to go for maximum efficiency then any constant pressure solution is probably not the answer, but I'm not sure that I need to optimize that heavily - I just worry about low solar production in the winters in Northern Idaho, and reducing my need for running a generator during those months. I'm not sure what to do, but I am concerned that I will regret moving forward with this expensive VFD system; however, I'm not sure what my alternatives are for my situation of needing water before I have a building where I could locate water system components like a pressure tank. My water needs before the house is completed will be much different (no toilets flushing with no house), so I could add things like a pressure tank and CSV at that time... but I'm not sure if I could/should run a submersible pump off a generator with no pressure tank before the house is built. I'm also wondering if it's possible to install 2 pumps of different sizes in the well (each on its own CSV), one for small flow and one for larger flow, where the small one would run most often and be more energy efficient due to being closer to its BEP.
Apologies if I've left out important details, my brain is fried after reading about wells for several hours.
380' deep
200' depth water first encountered @ 1gpm
240' depth water @ 3gpm
300' depth water @ 5gpm
340' depth water @ 8gpm
380' depth water @ 15gpm
30' static water level
I have a contractor lined up to build a house next spring. I currently have no power at the property, but plan to incorporate a large off grid power solution (inverter, batteries, solar, generator, etc). There are no buildings currently on the property with which to locate the components for a power or water system. I would like to have water functioning before the house build starts, which also means before I have an off grid power solution. My well driller is trying to sell me an expensive $8k VFD system (goulds 10gs30, 3as30, 3hp 3 phase motor, 4.25gal in well pressure tank) and saying that it is what he recommends for off grid people, with a plug for a generator at the pedestal that also contains the vfd drive. After tons of research I am not convinced that this is in my best interest economically. I am concerned not just for the longevity of the components in my water system, but also the total power requirements of it - not just power required to pump the water we will use but also the idle power draw of the VFD drive. I am not sure a CSV is going to be the best path either (in terms of efficiency), but I do like the simplicity of it and what it offers. If I want to go for maximum efficiency then any constant pressure solution is probably not the answer, but I'm not sure that I need to optimize that heavily - I just worry about low solar production in the winters in Northern Idaho, and reducing my need for running a generator during those months. I'm not sure what to do, but I am concerned that I will regret moving forward with this expensive VFD system; however, I'm not sure what my alternatives are for my situation of needing water before I have a building where I could locate water system components like a pressure tank. My water needs before the house is completed will be much different (no toilets flushing with no house), so I could add things like a pressure tank and CSV at that time... but I'm not sure if I could/should run a submersible pump off a generator with no pressure tank before the house is built. I'm also wondering if it's possible to install 2 pumps of different sizes in the well (each on its own CSV), one for small flow and one for larger flow, where the small one would run most often and be more energy efficient due to being closer to its BEP.
Apologies if I've left out important details, my brain is fried after reading about wells for several hours.